control signals bit description purpose/function 128 cycle start set by acrobasic to signal that cycle start has been pressed. 129

Control Signals
Bit Description Purpose/function
128 Cycle Start Set by AcroBasic to Signal that Cycle Start has been
pressed.
129 Estop Signals that Estop is On or Off.
130 Reset Signals ACR-MotionMax System to Do a Reset.
131 Feedhold Signals ACR-MotionMax that Feedhold is on.
132 Dry Run Signals ACR-MotionMax to run in Dry Run Mode
133 Auto/Step Signals control to Run in Auto or Step mode Auto=1 Step
=0
134 OK to Run If Not in Feed Hold, Estop, MDI Mode or Jog Mode (This
Signal Is Set by ACR-MotionMax)
135 Jog Mode Set by ACR-MotionMax when In Jog Mode
136 MDI Mode Set by ACR-MotionMax when in MDI Mode
137 Offsets Mode Set By ACR-MotionMax when Control is in Offsets
Screen
138 In Cycle Set by ACR-MotionMax when Control Goes in Cycle
139 Edit Mode Set by ACR-MotionMax when Control Goes in edit Mode
140 JoggedInCycle Set by ACR-MotionMax when the Control has jogged in
cycle
141 ReturnToPreJogPos Used by Mill max after a InCycle jog
142 OptionalStopActive When=1 Optional Stop will be acted on else they
will be ignored
143 Control Ready Set In ACR-MotionMax when Software Starts and
cleared When Program End
144 Homing Active Set In AcroBasic to Signal that a Homing operation
is in progress
145 Control Initialized Signal set by AcroBasic that Initialization
succeeded to ACR-MotionMax
146 Spindle Encoder Installed Used by ACR-MotionMax for Rigid Tapping
147 M Done Set by AcroBasic to Signal that a M code has finished
successfully
148 S Done Set By AcroBasic to Signal that a S code has finished
successfully
149 T Done Set By AcroBasic to Signal that a T code has finished
successfully
150 M Strobe Set By ACR-MotionMax when a M Code has been Sent to be
serviced by AcroBasic
151 S Strobe Set By ACR-MotionMax when a S Code has been Sent to be
serviced by AcroBasic
152 T Strobe Set By ACR-MotionMax when a T Code has been Sent to be
serviced by AcroBasic
153 Tool Change Active Set by ACR-MotionMax DLL to Signal M6 Sub needs
to do a change
154 Tool Change Done Set By AcroBasic in M6 Code to signal a tool
change has finished ok
155 Z @ T change Position Set By AcroBasic to Signal that Z is at the
Tool change Position
156 Tool Seek Active Set in AcroBasic T Strobe Code to Signal that
Magazine is Moving
157 Tool Seek Done Set by AcroBasic to Signal that the seek operation
is complete
158 Tool Seek Direction Set By ACR-MotionMax to Signal bi-directional
Magazine direction to Move
159 Tool Seek Speed Set By AcroBasic for Magazines that have Slow Down
Capabilities
160 MPG Enabled Set By AcroBasic to Signal ACR-MotionMax that Pendant
is Enabled
161 MPG X Select Set by AcroBasic to Signal ACR-MotionMax that Axis is
under Pendant Control
162 MPG Y Select Set by AcroBasic to Signal ACR-MotionMax that Axis is
under Pendant Control
163 MPG Z Select Set by AcroBasic to Signal ACR-MotionMax that Axis is
under Pendant Control
164 MPG 4 Select Set by AcroBasic to Signal ACR-MotionMax that Axis is
under Pendant Control
165 MPG 5 Select Set by AcroBasic to Signal ACR-MotionMax that Axis is
under Pendant Control
166 X.1 Mode Select Set by AcroBasic to Signal ACR-MotionMax that X.1
Mode is selected for Pendant Moves
167 X1 Mode Select Set by AcroBasic to Signal ACR-MotionMax that X1
Mode is selected for Pendant Moves
168 X10 Mode Select Set by AcroBasic to Signal ACR-MotionMax that X10
Mode is selected for Pendant Moves
169 X100 Mode Select Set by AcroBasic to Signal ACR-MotionMax that
X100 Mode is selected for Pendant Moves
170 X Home Done Set by AcroBasic to Signal ACR-MotionMax that Axis has
been Referenced
171 Y Home Done Set by AcroBasic to Signal ACR-MotionMax that Axis has
been Referenced
172 Z Home Done Set by AcroBasic to Signal ACR-MotionMax that Axis has
been Referenced
173 4 Axis Home Done Set by AcroBasic to Signal ACR-MotionMax that
Axis has been Referenced
174 5th Axis Home Done Set by AcroBasic to Signal ACR-MotionMax that
Axis has been Referenced
175 Magazine Reference Done Set By AcroBasic M18 to Signal
ACR-MotionMax that Magazine has been Referenced
176 Gear Change Active Set by AcroBasic when effecting a Gear change
177 Gear Change bit 0 Set by ACR-MotionMax to AcroBasic to signal
which Gear has been Requested (is a binary code)
178 Gear Change bit 1 Set by ACR-MotionMax to AcroBasic to signal
which Gear has been Requested (is a binary code)
179 Gear Change bit 2 Set by ACR-MotionMax to AcroBasic to signal
which Gear has been Requested (is a binary code)
180 Spindle Direction Bit Set by AcroBasic to signal ACR-MotionMax
Current Spindle direction is for M3/M4 outputs 1 fwd 0 rev
181 0 Speed Arrival bit Set by AcroBasic to Signal that Spindle is at
rest
182 Speed Arrival bit Set by AcroBasic to signal that spindle is
running at the commanded speed
183 Orient Complete Set By AcroBasic to signal that Spindle is at the
orient Position
184 Spindle Enable Set by ACR-MotionMax to signal that the spindle is
Enabled
185 Rigid Tapping Active Signal will be 1 when the ACR-MotionMax
Control is Rigid Tapping
186 Tapping Active Signal will be 1 when ACR-MotionMax is running a
Tapping cycle
187 4th Axis Present Set by AcroBasic to ACR-MotionMax informing
control of 4th axis presence
188 4th Axis Clamped Set by AcroBasic to ACR-MotionMax signaling that
4th Axis is locked
189 Contouring Set by ACR-MotionMax to signal that a contouring mode
is active
190 SpindleRunning Set in AcroBasic to form logic to turn Spindle back
on if paused
191 Reserved
192 Over Travel Active Set by AcroBasic to ACR-MotionMax of an
existing OverTravel
193 EnableVirtualEstop Set to Allow Virtual Estop Button on GUI
194 V Estop Status Status Signal used by ACR-MotionMax of VEstop
195 Reserved for future use
196 Reserved for future use
197 Reserved for future use
198 Reserved for future use
199 Reserved for future use
200 Reserved for future use
202 Program Running Set by ACR-MotionMax signals that a G Code program
is running InCycle
203 Program Modified Set by ACR-MotionMax when the current program has
been altered
204 to 212 Reserved for future use (Don’t Use)
213 Digital FOV Bit0 4 bit Code for External Feedrate Override
Switches to
214 Digital FOV Bit1 Create logic 0 – 100 %
215.
Digital FOV Bit2
216.
Digital FOV Bit3
217.
Digital ROV Bit0 4 bit Code for External Rapid Override Switches
218.
Digital ROV Bit1
219 Digital ROV Bit2
220 Digital ROV Bit3
221 Digital SOV Bit0 4 bit Code for External Rapid Override Switches
222 Digital SOV Bit1
223 Digital ROV Bit2
224.
Digital ROV Bit3
225 to 248 Scratch Pad bits (Bits for the User to use as status bits)
249 Reserved Used by ACR-MotionMax for internal Error Messages display
250 User Error bit 0 Bits 250 to 255 form a binary code for Error
Messages to send to ACR-MotionMax
251 User Error bit 1
252 User Error bit 2
253 User Error bit 3
254 User Error bit 4
255 User Error Bit 5 See: Setting Up User Defined Error Messages

  • AHRC2514ADD1 NACIONES UNIDAS AHRC2514ADD1 ASAMBLEA GENERAL DISTR GENERAL 13
  • W INCHESTER ANIMAL HOSPITAL 901 NORTH LOUDOUN STREET WINCHESTER
  • INTERSECTORAL WORKSHOP ON VIOLENCE AGAINST WOMEN WITH DISABILITIES AND
  • ≥ NOWY PORT NABRZEŻE OLIWSKIE STANOWISKO ODC [M] POLERY
  • REGULAMIN SEKCJI PRAWA FARMACEUTYCZNEGO POLSKIEGO TOWARZYSTWA FARMACEUTYCZNEGO POSTANOWIENIA OGÓLNE
  • REMARKS PREPARED FOR DELIVERY BY ANTONIO MARIA COSTA EXECUTIVE
  • GUÍA DE REFERENCIA DE LAS TECLAS DE ACCESO RÁPIDO
  • EMBAJADA DE ESPAÑA AMÁN JORDANIA ALTAS – REGISTRO DE
  • QUALITY ASSURANCE CONTENTS INTRODUCTION INSPECTION PROCESS  AUDIT
  • POLS STUDENT JANUARY 2006 CLAPSA DMITRI LONG WAY TOWARDS
  • OBČINA RADLJE OB DRAVI SOFINANCIRANJE ŠPORTNIH PROGRAMOV OBRAZEC
  • CONCERTI 2009 – 2010 8° CONCERTO AUDITORIUM RAI ARTURO
  • LAS NORMAS CON QUE VIVES CAPÍTULO 7 DEL LIBRO
  • ŠTEVILKA 0010429920185 DATUM 13 12 2018 ODGOVOR NA POSLANSKO
  • SCHEDULE “A” – VOLUME UNIT PRICE MAJOR WORKS CONTRACT
  • STANOWISKO KRAJOWEJ RADY SĄDOWNICTWA Z DNIA 11 PAŹDZIERNIKA 2007
  • 2012 WINTEREARLY SPRING THURSDAY NIGHT TRACK RACING SERIES FEBRUARY
  • MINISTARSTVO ZAŠTITE OKOLIŠA I PROSTORNOG UREĐENJA 1370 NA TEMELJU
  • SCHOOLS VISITS YEARS 713 BRINGING YOUR STUDENTS TO THE
  • AKER SYKEHUS NEDENSTÅENDE ER MENT Å SKULLE GI SVAR
  • MENO PRIEZVISKO ADRESA A TELEFÓNNY KONTAKT ZÁKONNÉHO ZÁSTUPCU RIADITEĽSTVO
  • 2 NATIONAL REPORT NAMIBIAN NATIONAL BIODIVERSITY PROGRAM REPUBLIC OF
  • POSSESSIVES E …CONNECTIONS… FOR ADDITIONAL APOSTROPHERELATED MATERIAL SEE CONTRACTIONS
  • KRATKO POROČILO O TEDNU ZA NAŠE ZDRAVJE LETOŠNJI TEDEN
  • SECTION COVER PAGE SECTION 32 31 00 20180815 CHAIN
  • LESSON 7 AMAZING JOURNEYS LOOK AT THE PICTURE WHAT
  • GUIDELINES FOR THE APPOINTMENT OF ACTING JUDICIAL OFFICERS
  • CASOS DE ÉXITO MICROSOFT MICROSOFT® WINDOWS® XP TABLET PC
  • ZAŁĄCZNIK NR 2 DO SZCZEGÓŁOWYCH WARUNKÓW KONKURSU ZP4240217 ŚWIADCZENIE
  • DC45A (411) PAGE 9 OF 9 NEW JERSEY DEPARTMENT