NStraight Connector 17 Ote Click On “Show/Hide ¶” Button

nstraight connector 17 ote: click on “show/hide ¶” button to reveal specifier notes throughout section. delete this text when editing i

NStraight Connector 17 ote: Click on “Show/Hide ¶” button to reveal
"Specifier Notes" throughout section. Delete this text when editing is
complete.
1.
GENERAL
1.
CONDITIONS AND REQUIREMENTS
A.
The General Conditions, Supplementary Conditions, and
Division 01 – General Requirements apply.
1.
SECTION INCLUDES
Specifier Note: Delete items below that are not included in this
section.
A.
Solar-control films.
B.
[Insert item description.]
1.
RELATED SECTIONS
Specifier Note: In this article, specify work specified in other
sections that is related to work of this section.
A.
Section 08 80 00 - Glazing: Substrate for application of
solar-control film.
Specifier Note: The following paragraph is a sample that may be used
in this article. Add to or delete from the following as appropriate
for the specific project.
B.
Section [xxxxx] – [Section Title]: [Include brief
description of work specified in another section that is
related to the work of this section.]
1.
REFERENCES
Specifier Note: List standards referenced elsewhere in this section
including designations and titles. Delete those standards not retained
elsewhere in this section after editing.
A.
ASTM International (ASTM):
1.
ASTM E903 - Test Method for Solar Absorptance,
Reflectance, and Transmittance of Materials Using
Integrating Spheres.
1.
DEFINITIONS
A.
Dual-Reflective Solar-Control Films: Film products where
interior visible light reflectance is less than exterior
visible light reflectance. Lower interior reflectance
provides improved visibility from interior to exterior
without affecting the film’s solar performance.
2.
PERFORMANCE REQUIREMENTS
A.
Dual-reflective solar-control film products shall help
improve solar heat and UV reduction, glare reduction,
privacy, fade protection, and aesthetic characteristics
when applied to glass surfaces.
B.
Ultraviolet Transmission: Provide solar-control films
with UV absorbing materials that limit the weighted UV
Transmission to one (1) percent or less when measured
according to ASTM E903.
C.
Provide solar-control films that do not have a masking
sheet.
3.
SUBMITTALS
Specifier Note: In this article, specify various types of data to be
furnished by the contractor before, during, or after construction.
Topics included in this article are: product data, shop drawings,
samples, design data, test reports, certificates, manufacturers’
instructions, manufacturers’ field reports, qualification statements,
and closeout submittals.
A.
Submit under provisions of Section [01 33 00] [______].
B.
Product Data: Submit for each product specified
indicating:
1.
Performance properties.
2.
Preparation and installation instructions and
recommendations.
3.
Storage and handling recommendations.
C.
Samples: For each type of solar-control film specified,
two (2) samples, 12 inches square.
D.
Qualification Data: Submit documentation indicating
qualifications of solar-control film manufacturer.
E.
Operation and Maintenance Data: Submit for solar-control
film to include in maintenance manuals.
F.
Warranty: Submit sample special warranty specified in this
section.
1.
QUALITY ASSURANCE
Specifier Note: In this article, describe qualifications, regulatory
requirements, certifications, field samples, mock-ups, and
pre-installation meetings.
A.
Manufacturer Qualifications: A qualified manufacturer that
has a minimum of 10 years of documented experience
manufacturing solar-control films similar to be used for
this project.
B.
Installer Qualifications: A firm that is authorized by
solar-control film manufacturer to install film in
accordance with guidelines set forth by the manufacturer.
C.
Source Limitations: Obtain each type of solar-control film
from same manufacturer.
Specifier Note: Retain the following paragraph and subparagraphs if
the project requires one. Use mockups on large or complex projects.
D.
Mock-ups: Build mock-ups to verify selections made under
sample submittals and to evaluate surface preparation
techniques and application workmanship.
1.
Construct mock-ups in the location and of the size
indicated or, if not indicated, as directed by
Architect.
2.
Approved mock-ups may become part of the completed
work if undisturbed at time of Substantial Completion.
E.
Pre-installation Conference: Conduct conference at project
site to discuss methods and procedures relating to
installation of the solar-control films.
1.
DELIVERY, STORAGE AND HANDLING
A.
Deliver, store, and handle materials in manufacturer's
protective packaging.
B.
Store and protect materials according to manufacturer's
written recommendations to prevent damage from
condensation, temperature changes, direct exposure to
sun, or other causes.
2.
SITE CONDITIONS
A.
Ambient Conditions: Maintain temperature, humidity, and
ventilation within limits recommended by manufacturer.
3.
LIMITED WARRANTY
A.
Manufacturer's Limited Warranty: Certain restrictions
apply. The Manufacturer’s Limited Warranty can be viewed
in full by clicking here.
2.
PRODUCTS
1.
MANUFACTURERS
A.
Basis-of-Design Product: The design for
dual-reflective solar-control films is based on LLumar®
Dual-Reflective Series Solar-Control Films
manufactured by an Eastman Performance Films, LLC, 575
Maryville Centre Drive, St. Louis, Missouri 63141;
Telephone: 800-851-7781 (Option 2);
https://northamerica.llumar.com/contact-llumar; Web
Site: www.llumar.com.
B.
Representative: [Insert contact information.]
Specifier Note: Select either of the following two (2) paragraphs and
delete the other.
C.
Substitutions will be considered, subject to compliance
with requirements of this section, under provisions of
Section 01 60 00.
1.
SOLAR-CONTROL FILMS
A.
Solar-Control Film: LLumar® Dual-Reflective DR05SRCDF
Film with the following performance characteristics when
applied to the interior surface of single-pane, 1/4-inch
clear glass:
% Total Solar Transmittance
6
% Total Solar Reflectance
50
% Total Solar Absorptance
44
% Visible Light Transmission
6
% Visible Light Reflection - Exterior
59
% Visible Light Reflection - Interior
16
Winter U-Value
0.87
Shading Coefficient
0.20
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.56
Solar Heat Gain Coefficient
0.17
% Total Solar Energy Rejection
83
Light-to-Solar Heat Gain Ratio
0.35
% Summer Solar Heat Reduction
79
% Winter Heat Loss Reduction
16
% Glare Reduction
93
Thickness without Liner
43 µ
Film Color
Warm Gray
Specifier Note: Select any of the following four (4) paragraphs and
delete the others. If retaining more than one (1) type indicate
locations on Drawings or add a schedule at the end of this section.
B.
Solar-control Film: LLumar® Dual-reflective DR15SRCDF Film
with the following performance characteristics when
applied to the interior surface of single-pane, 1/4-inch
clear glass:
% Total Solar Transmittance
15
% Total Solar Reflectance
34
% Total Solar Absorptance
51
% Visible Light Transmission
16
% Visible Light Reflection - Exterior
38
% Visible Light Reflection - Interior
13
Winter U-Value
0.91
Shading Coefficient
0.33
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.62
Solar Heat Gain Coefficient
0.29
% Total Solar Energy Rejection
71
Light-to-Solar Heat Gain Ratio
0.55
% Summer Solar Heat Reduction
65
% Winter Heat Loss Reduction
12
% Glare Reduction
82
Thickness without Liner
43 µ
Film Color
Warm Gray
C.
Solar-control Film: LLumar® Dual-reflective DRN25SRCDF
Film with the following performance characteristics when
applied to the interior surface of single-pane, 1/4-inch
clear glass:
% Total Solar Transmittance
21
% Total Solar Reflectance
27
% Total Solar Absorptance
52
% Visible Light Transmission
22
% Visible Light Reflection - Exterior
29
% Visible Light Reflection - Interior
12
Winter U-Value
0.91
Shading Coefficient
0.41
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.62
Solar Heat Gain Coefficient
0.35
% Total Solar Energy Rejected
65
Light-to-Solar Heat Gain Ratio
0.63
% Summer Solar Heat Reduction
57
% Winter Heat Loss Reduction
12
% Glare Reduction
75
Thickness without Liner
43 µ
Film Color
Warm Gray
D.
Solar-control Film: LLumar® Dual-reflective DRN35SRCDF
Film with the following performance characteristics when
applied to the interior surface of single-pane, 1/4-inch
clear glass:
% Total Solar Transmittance
30
% Total Solar Reflectance
20
% Total Solar Absorptance
50
% Visible Light Transmission
34
% Visible Light Reflection - Exterior
20
% Visible Light Reflection - Interior
13
Winter U-Value
0.94
Shading Coefficient
0.50
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.67
Solar Heat Gain Coefficient
0.44
% Total Solar Energy Rejected
56
Light-to-Solar Heat Gain Ratio
0.77
% Summer Solar Heat Reduction
46
% Winter Heat Loss Reduction
9
% Glare Reduction
61
Thickness without Liner
43 µ
Film Color
Warm Gray
E.
Solar-control Film: Vista™ by LLumar® Dual-reflective
Series Ultima V14SRCDF Film with the following performance
characteristics when applied to the interior surface of
single-pane, 1/4-inch clear glass:
% Total Solar Transmittance
7
% Total Solar Reflectance
44
% Total Solar Absorptance
49
% Visible Light Transmission
10
% Visible Light Reflection - Exterior
53
% Visible Light Reflection - Interior
24
Winter U-Value
1.01
Shading Coefficient
0.25
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.80
Solar Heat Gain Coefficient
0.22
% Total Solar Energy Rejected
78
Light-to-Solar Heat Gain Ratio
0.45
% Summer Solar Heat Reduction
73
% Winter Heat Loss Reduction
2
% Glare Reduction
89
Thickness without Liner
43 µ
Film Color
Blue Gay
F.
Solar-control Film: Vista™ by LLumar® Dual-reflective
Series Celeste V18SRCDF Film with the following
performance characteristics when applied to the interior
surface of single-pane, 1/4-inch clear glass:
% Total Solar Transmittance
14
% Total Solar Reflectance
34
% Total Solar Absorptance
52
% Visible Light Transmission
20
% Visible Light Reflection - Exterior
39
% Visible Light Reflection - Interior
21
Winter U-Value
1.01
Shading Coefficient
0.34
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.80
Solar Heat Gain Coefficient
0.30
% Total Solar Energy Rejected
70
Light-to-Solar Heat Gain Ratio
0.67
% Summer Solar Heat Reduction
63
% Winter Heat Loss Reduction
2
% Glare Reduction
77
Thickness without Liner
43 µ
Film Color
Blue Gray
G.
Solar-control Film: Vista™ by LLumar® Dual-reflective
Series Luminance V28SRCDF Control Film with the following
performance characteristics when applied to the interior
surface of single-pane, 1/4-inch clear glass:
% Total Solar Transmittance
22
% Total Solar Reflectance
28
% Total Solar Absorptance
50
% Visible Light Transmission
30
% Visible Light Reflection - Exterior
32
% Visible Light Reflection - Interior
22
Winter U-Value
0.99
Shading Coefficient
0.42
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.77
Solar Heat Gain Coefficient
0.37
% Total Solar Energy Rejected
63
Light-to-Solar Heat Gain Ratio
0.81
% Summer Solar Heat Reduction
55
% Winter Heat Loss Reduction
4
% Glare Reduction
66
Thickness without Liner
43 µ
Film Color
Blue Gray
H.
Solar-control Film: Vista™ by LLumar® Dual-reflective
Series Mirage V38SRCDF Film with the following performance
characteristics when applied to the interior surface of
single-pane, 1/4-inch clear glass:
% Total Solar Transmittance
28
% Total Solar Reflectance
23
% Total Solar Absorptance
49
% Visible Light Transmission
38
% Visible Light Reflection - Exterior
25
% Visible Light Reflection - Interior
17
Winter U-Value
1.01
Shading Coefficient
0.50
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.78
Solar Heat Gain Coefficient
0.43
% Total Solar Energy Rejected
57
Light-to-Solar Heat Gain Ratio
0.88
% Summer Solar Heat Reduction
48
% Winter Heat Loss Reduction
2
% Glare Reduction
57
Thickness without Liner
43 µ
Film Color
Blue Gray
I.
Solar-control Film: Vista™ by LLumar® Dual-reflective
Series Nuance V48SRCDF Film with the following performance
characteristics when applied to the interior surface of
single-pane, 1/4-inch clear glass:
% Total Solar Transmittance
36
% Total Solar Reflectance
14
% Total Solar Absorptance
50
% Visible Light Transmission
46
% Visible Light Reflection - Exterior
15
% Visible Light Reflection - Interior
11
Winter U-Value
1.02
Shading Coefficient
0.59
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.84
Solar Heat Gain Coefficient
0.52
% Total Solar Energy Rejected
48
Light-to-Solar Heat Gain Ratio
0.88
% Summer Solar Heat Reduction
37
% Winter Heat Loss Reduction
1
% Glare Reduction
48
Thickness without Liner
43 µ
Film Color
Blue Gray
J.
Solar-control Film: Vista™ by LLumar® Dual-reflective
Series Sunrise Bronze V33BRSRCDF Film with the following
performance characteristics when applied to the interior
surface of single-pane, 1/4-inch clear glass:
% Total Solar Transmittance
23
% Total Solar Reflectance
36
% Total Solar Absorptance
41
% Visible Light Transmission
38
% Visible Light Reflection - Exterior
24
% Visible Light Reflection - Interior
18
Winter U-Value
0.94
Shading Coefficient
0.40
% Ultraviolet Ray Protection (300nm-380nm)
>99
Emissivity
0.67
Solar Heat Gain Coefficient
0.35
% Total Solar Energy Rejected
65
Light-to-Solar Heat Gain Ratio
1.09
% Summer Solar Heat Reduction
57
% Winter Heat Loss Reduction
9
% Glare Reduction
57
Thickness without Liner
43 µ
Film Color
Bronze
3.
SOLAR-CONTROL FILM ACCESSORIES
A.
General: Provide accessories either manufactured by or
acceptable to solar-control film manufacturer for
application indicated, and with a proven record of
compatibility with surfaces contacted in installation.
B.
Adhesive: Films with CDF designation utilize a water-
activated, dry-adhesive system that forms a molecular bond
between the film and glass. Films with a PS designation
utilize a pressure-sensitive adhesive which is activated
by pressure and water. It is characterized by its
permanently tacky nature and its installation ease.
Protect adhesive from contamination by applying a release
liner that will be removed and discarded at installation.
C.
Cleaners, Primers, and Sealers: Types recommended by
solar-control film manufacturer.
1.
EXECUTION
1.
EXAMINATION
A.
Examine substrates for compliance with requirements
and for conditions affecting performance of
solar-control film including glass that is broken,
chipped, cracked, abraded, or damaged in any way.
B.
Proceed with installation only after unsatisfactory
conditions have been corrected.
2.
PREPARATION
A.
Clean substrates thoroughly prior to installation.
Provide additional scrubbing of perimeter area with
X-100® solution.
B.
Prepare substrates using methods recommended by film
manufacturer to achieve the best results for the
substrate under project conditions.
C.
Protect window frames and surrounding surfaces to
prevent damage during installation.
3.
INSTALLATION
A.
Install in accordance with manufacturer’s written
instructions.
B.
Install with no gaps or overlaps.
C.
If seamed, make seams non-overlapping.
D.
Do not remove release liner from film until just
before each piece of film is cut and ready for
installation.
E.
Custom cut to the glass with neat, square corners and
edges to within 1/8-inch of the window frame. Use
X-100® solution for the application for films
designated with CDF adhesive, unless otherwise
recommended by the manufacturer. For Safety
Solar-Control Films designated with PS adhesive, use
Film-On for application.
F.
Remove air bubbles, blisters, and other defects. Be
careful to remove “fingers” to eliminate any
contamination or excess water pockets. It is crucial
to remove as much water as possible during
installation.
4.
FIELD QUALITY CONTROL
A.
After installation, view film from a distance of 10
feet against a bright uniform sky or background. Film
shall appear uniform in appearance with no visible
streaks, wrinkles, banding, thin spots or pinholes.
B.
If installed film does not meet these criteria, remove
and replace with new film.
5.
CLEANING AND PROTECTION
A.
Remove excess mounting solution at finished seams,
perimeter edges, and adjacent surfaces.
B.
Use cleaning methods recommended by solar-control film
manufacturer.
C.
Replace films that cannot be cleaned.
D.
Protect installed products until completion of project.
E.
Touch-up, repair or replace damaged products before
Substantial Completion.
END OF SECTION
Straight Connector 21 Group 1
Project Name
Project Location
Straight Connector 3
Date
Solar-control Films
Project Number
08-87-13